Shaft Size
|___|
Resolution - bits
07 = 1"-keyway 1/4"
|
hohner |
Hohner Corporation |
| Home | Distributors | Terms | About Us | Accessories | Download 3D AutoCAD |
|
Series 88 absolute parallel encoder |
|
|
8 | 8 | X | X | - | 2 | 0 | X | X | - | 0 | 0 | X | X | |||||||||||
|
Shaft Size |
|
|___| |
|
Resolution - bits |
|||||||||||||||||||||
| 03 = 1/2" | | | 10 = 10 bit | |||||||||||||||||||||||
| 05 = 5/8"-keyway 3/16" | | | 12 = 12 bit | |||||||||||||||||||||||
|
07 = 1"-keyway 1/4" |
Output Code | ||||||||||||||||||||||||
| 16 = 24 mm | 20 = binary, 16 pin | ||||||||||||||||||||||||
| 17 = 30 mm | 24 = gray, 16 pin | ||||||||||||||||||||||||
| 25 = 1 - 1/4" | 29 = gray, 6 ft cable | ||||||||||||||||||||||||
| 30 = binary, 6 ft cable | |||||||||||||||||||||||||
| Technical Data | Connection Options | ||||
| Operating temp: | - 20 ...+ 60 degrees C | Bin / Gray | 16 / 21 pole | Cable | |
| - 4 ...+ 140 degrees F | PS GND | 1 | Black | ||
| Higher Temperature: | Please consult | PS 12 ... 24 V | 2 | Red | |
| Power supply: | 12 - 24V | 2-0 | 3 | White | |
| Current consumption: | 100 mA (max.) | 2-1 | 4 | Blue | |
| Line driver output max: | 50 mA per channel | 2-2 | 5 | Yellow | |
| Weight: | 1.0 Kg | 2-3 | 6 | Green | |
| Protection: | IP 54 | 2-4 | 7 | Violet | |
| Housing: | Aluminum | 2-5 | 8 | Brown | |
| Shaft: | Aluminum | 2-6 | 9 | Pink | |
| Bearings: | 2 x 6008 ZZ | 2-7 | 10 | Turquoise | |
| Torque: | 0.4 oz/in (3 N-cm) | 2-8 | 11 | Grey | |
| Humidity: | Up to 98% permissible | 2-9 | 12 | Orange | |
| Speed: | 3000 RPM max. | 2-10 | 13 | Green / Red | |
| Shock: | 10g (6msec) | 2-11 | 14 | Red / Blue | |
| Vibration: | 5g (500 Hz) | 2-12 | 15 | Yellow / Red | |
| Shaft load: | Supports its own weight | cw = N / C to pin 16 | Red / Black | ||
| ccw = pin 16 to GND | |||||
| Output | |||||
| Count will increment in cw direction | |||||
 |
|||||
| Mounting Instructions |
|
Mount fixture to the
machine with three screws and three washers, M6 or 1/4". Slide the
encoder onto the shaft. With the setscrews, tighten the hollow shaft
encoder onto the shaft with a minimum clearance of 1/16" between fixture and
encoder. This assembly allows the shaft to float and increases the
lifetime of the bearings. Connect the encoder as per wiring specifications. Make sure power supply is within the proper voltage and current rating. Encoder can be mounted with the setscrew on the machine side or on the opposite side for either CW or CCW. See datasheet for CW and CCW directions of the outputs. Technical data for mount: 1/8" stainless steel wire
|
| Dimensions |
|
|
| Hohner Corp. | Tel: (905) 563 4924 |
| 5536 Regional Road 81 | Fax: (905) 563 7209 |
| Beamsville, Ontario | E-mail: hohner@hohner.com |
| Canada L0R 1B3 | Web: www.encoderonline.com |
